Dremel tools are versatile and useful to have around the home.
Among them is a tool for routing, cutting, and sanding called a Dremel rotary tool.
These handheld power tools come with a wide variety of attachments that can be added to create different types of cutters or router bits.
Many of these accessories can fit into a standard 1/8-inch collet on your Dremel rotary cutting machine.
A Dremel router bit is one such accessory designed specifically for use as a router in either small or large projects.
There are two types of bits available: those with a spiral design and those with down spiral designs known as soldiers because they tend to create swirls on the surface of the cut.
As with any type of bit, exact setup and use are imperative to achieve the best results.
This guide will teach you how to properly attach Dremel router bits as well as how to make these bits work for your projects.
Your Dremel rotary cutter machine A standard 1/8-inch collet attachment Aligning pin or wrench Routing base
Step 1 – Determine Your Bit Orientation
Before attaching a routing base,
it’s important that you first determine which way you want to place your cutting bit about its housing.
On some bases, this design is reversible so they can be used either vertically or horizontally depending on what you want to do.
Once you’ve decided, make sure the router bit is facing in the opposite direction and attach it using the collet.
You will also need to place a small aligning pin or wrench onto one of the three pins on your routing base before attaching it.
This ensures that your bit is properly positioned and installed properly into the Dremel rotary cutter machine for use.
You can now move on to installing and setting up your routing base if this hasn’t been done already as described in step two.
Step 2 – Attach Your Base
Place your Dremel router bit with attached collet into its corresponding base according to those instructions above under “determine your bit orientation.
If you have an aligning pin or wrench, make sure it’s placed onto one of the three pins on your base.
Once this is done, you can tighten the collet down with an aligning pin or wrench according to manufacturer directions.
Step 3 – Attach Your Base to Your Dremel Rotary Cutting Machine
Your Dremel router bit comes with complete instructions for this step, though it should be fairly straightforward.
Most models will simply require you to remove a cap and place the base into place before attaching that cap back on after adjusting if necessary.
You’ll know your bit is securely attached when all parts move as they should and nothing wobbles too much during use.
Step 4 – Adjust Router Bit Depth
Now that your bit is secure in its base, you’ll need to adjust the depth of the cut.
Turn on your Dremel rotary tool and bring it up to speed before setting the depth at its lowest point.
This is done by rotating a knob or screw on the side of your base according to manufacturer specifications for safe operation.
Step 5 – Cut Your First Piece
Begin routing whatever piece you’re using with the router bit itself attached to your Dremel rotary cutting machine.
Guide it along slowly, taking care not to place excessive pressure onto either what you are cutting or into the bit itself which might cause damage or defective results.
Just as with any type of bit used for this purpose, take care not to move too fast, creating friction between the surface of the bits and that of the material you are routing.
Step 6 – Cut Your Second Piece
Once you’ve cut your first piece, turn off the Dremel rotary tool and remove the bit from its base before rotating it to use as a router head on another side of that piece.
Repeat steps 4 through 5 above according to manufacturer specifications for safe operation once again.
Some Dremel router bits come with an up spiral design, while others feature a down spiral design.
It’s important to keep this in mind when using these products because certain types of bits tend to create swirls on the surface of routed materials.
Because of their orientation so be careful when making your adjustments if necessary after testing out each type.
This guide will show you how to do so.
Step 7 – Test the Bit Orientation on Your First Piece
To begin, adjust your depth to its lowest point and make a path across the surface of your first piece using your Dremel router bit as described in step 5 above.
You can now take a quick pass over this area with high grit sandpaper (1200 or higher) which should give you enough information about how these two types of bits will work based on that test alone.
If you notice ugly swirl marks after running this test, switch your collet orientation accordingly before moving on to steps 8 through 11 below.
Once you’re done, turn off the Dremel rotary tool and remove it from its base as well before returning it for use with another side of your piece.
Step 8 – Test the Bit Orientation on Your Second Piece
Repeat step 7 above, only this time you’ll want to test out each type and their orientation to determine which will work best based on that test alone before moving on to steps 9 through 11 below.
Turn off the Dremel rotary tool once your true test is completed with results determined.
Step 9 – Determine Which Type of Bit Works Best
Once again turn on your Dremel rotary tool along with its corresponding base to establish both are securely attached.
Once ready, place this bit into place so it’s secured by using an aligning pin or wrench according to manufacturer directions before turning it off again. Now you can go on to step 10 below.
Step 10 – Make Your Cuts
Begin routing your material according to manufacturer specifications for safe operation included with your purchase before turning off the Dremel rotary tool and removing it from its base again afterward.
Turn on a finishing sander, an orbital sander, or any other type of sanding machine in conjunction with high grit sandpaper between 2000 and 3000 before gently going over the surface of your routed piece one time or until you notice that all marks left behind by the router bit are gone.
Be sure not to take this anywhere near wood filler, paint, stain, etc.
if you desire results free from defects due to these residues being left behind upon finishing work. Finally, clean up with a microfiber cloth before moving on to step 11 below.
Step 11 – Clean Your Bit
Once everything is back in place, you can now clean your bit with a piece of Scotch Brite pad or anything abrasive which won’t damage the surface according to manufacturer directions included with your purchase.
This will help maintain its cutting power for future routing work.
You can now go ahead and store this bit away for future use according to manufacturer specifications as well.
Which Is The Best Dremel Router?
There are so many brands of routers but people want the best router that they must need to know about which brand carries the most features, quality services and carries low rate price tag also.
This router kit comes with all needed accessories like collets, wrench, template guide bushings, etc. It has an exclusive design also.
This router kit has a stronger motor which runs on 2 horsepower and it can produce speed between 16000-35000 rpm. It is a portable, lightweight, and easy-to-handle router kit.
This router is tested powerful and high efficient in performance compared to other Dremel routers.
This router carries the most advanced features like fixed or plunge base, variable speed function, etc.
The best thing about this product is that it comes with a 1-year warranty and a 30-day money-back guarantee.
What Is A Router?
A router is a hand tool or machine used to hollow out an area such as cutting dadoes, rabbets, and mortises.
Some of the most popular cut types made by a router are groundcovers, chamfers, and flush trim.
Routers are very versatile tools that can be used in many applications from cutting dadoes or rabbets to rounding over or chamfering the edge of aboard.
The router is considered by many to be the single most versatile tool in a woodshops arsenal.
How To Use A Router?
There are different types of routers based on functions and working capabilities.
Knowing the type will help you determine which one to buy for your specific needs.
Here we have two main types: Fixed base and plunge routers.
Each has its unique characteristics and advantages/disadvantages when it comes to using them for various purposes.
Fixed Base Router: This type features a base with an opening that contains the cutter.
The opening is at the bottom of the base and this type does not plunge like a plunge router.
With fixed bases, you must manually lock it into position before operating the tool; then unlock it to move to another work area or finish routing your cut.
You can use them on tabletops using mounting rings, but there are also routers with dedicated bases. Some models come with their built-in stands for greater stability if you need to do some freehand routing.
Plunge Router: This one has an opening in its base with an adjustable sub-base below that fits inside.
Below this sub-base is where all adjustments operate and where most of the controls are located as well, with some models featuring rack-and-pinion type adjustment for quick tool height adjustments.
A plunge router is great if you want to easily switch between routing operations or join two workpieces end-to-end at a perfect joint line without the need to adjust for different depths.
You can also use them freehand, but this will require more care, since it may be difficult to control their movements while maneuvering inside the opening in your workpiece.
Final Say & Tips
The most important tip to consider is that you should always read the manual before using a router.
This way, you can know its features and limitations as well as how to properly use it for maximum safety and performance.
You must also keep your tools clean and always check their condition before use since a dirty or faulty tool may cause accidents.
Also don’t forget to wear all required safety gear, such as boots,
gloves, earmuffs, eyewear, etc., according to your work conditions.
Some other tips might come in handy when using a router: Make sure there’s enough clearance on both sides of the cut area.
Always place your workpiece against an edge guide whenever possible this will allow square cuts without the need to angle the router.
The depth of your cut must be carefully calculated.
Strive for a shallower depth, especially when cutting across the grain because this increases the risk of tear-out.
You can also put wax or other finish on your board before routing so you’ll have an easier time cleaning up after yourself later on.
Lastly, if you don’t feel confident enough with how to use this tool properly, consider practicing first using some scrap wood or even better if you can find someone who’s experienced to give you some simple lessons first.
Remember that safety is always the priority and these tips will help you stay safe while using your new Dremel plunge router kit effectively.