How to Sharpen a Pole Saw Blade?
Pole saws are designed with an adjustable blade, which is capable of reaching high above the ground.
This makes it possible to trim or cut limbs close to the trunk of a tree, without having to use a ladder. A pole saw should be handled carefully because it may make contact with overhead limbs, if not used correctly.
Safety gear should always be worn when using one of these tools.
To maintain your pole saw, you’ll need to sharpen its blade on occasion, but this can be done by the owner.
Five Most Easiest And Safe Steps
Step 1 – Get Familiar With Your Saw
Before attempting to actually sharpen your saw’s blade, familiarize yourself with how it works first.
The safety latch must be unlocked before you can adjust its position.
When you get to the blade, notice how it is attached to a pommel nut at the end of the tool’s pole.
This is where you should focus your attention while sharpening your blade.
Step 2 – Clean Off Dirt and Clippings
After removing any dirt or clippings from the saw, spray a light coat of lubricating oil on its faceplate and pommel nut assembly.
The outdoor elements cause this part to wear out quickly, so it might need more than just a quick cleaning once in a while.
While you have your saw disassembled in this manner, go ahead and inspect other components for damage as well.
Check to see if the pull rope needs replacing because it will eventually stretch out and snap. Also, look at the teeth on your blade and see if they need to be sharpened or replaced.
Step 3 – Identify the Angle of the Blade
With your safety latch unlocked, you can now adjust your pole saw’s angle.
This feature allows you to make cuts from above, which is safer for most people. You may use a protractor or some other type of angle-measuring device in order to get the appropriate angle for trimming limbs and branches.
Measurements are usually taken by starting at zero degrees, moving counterclockwise till you find the right number. Once you have this measurement, it will be easy to maintain an even cut when using your tool again in the future.
Keep in mind that the higher your blade is from the ground, the more likely it will also be to get nicked by rocks or other hard objects.
Step 4 – Sharpen the Blade
After you have made a mental note of your saw’s angle, use a file with a handle attached to it in order to sharpen its blade.
If you don’t have this type of file handy, you can always purchase one that attaches to a handle for just a few dollars at most hardware stores near you.
Simply run it along those ridges on both sides of your saw several times until they become smooth again.
Move away from the tip and toward either end as needed for an even cut.
Doing so also helps prevent damage from occurring as soon as it hits a branch or limb.
Step 5 – Take Care of Your Blade
If you need to replace your saw’s blade, don’t worry about spending a lot of money on one.
These types of blades can be found in most hardware stores for less than fifty dollars.
It’s best to purchase the same brand as your pole saw so that fitting it on will not be an issue later down the line.
You should store this part away when finished with its sharpening and inspection and keep it out only when you need to use your tool again in order to avoid accidental damage.
Sharpening your pole saw’s blade is just like sharpening any other type of cutting utensil and takes only a few minutes to accomplish before it needs to be used again.
Sharpening the pole saw blade with a grinder
Use a file to sharpen the teeth. Make sure not to miss any one of them.
Sharpen it according to the angle you have identified earlier.
Keep sharpening the pole saw blade until all its teeth become smooth and wrinkle-free, or at least it should be no longer jagged and not too deep for safety purposes.
After filing the teeth on both sides, you can now tighten the bolt that holds up your blade.
Make sure it is tight enough to prevent it from crashing down after cutting through a tree limb, but not too hard to where it will require an excessive amount of effort to finally remove your pole saw’s blade.
Keep Up With Maintenance
After you sharpen your blade, remember to maintain it again in the future when it becomes dull.
When this happens, clean off all dirt and debris before putting your safety latch back in its original position.
The direction of your blade’s teeth should be facing towards the ground while you are not using it in order to minimize damage from occurring at that end.
You can also spray lubricating oil on its bolt assembly, which will prolong the life of your tool by making it easier for both halves to slide against each other without causing any unnecessary friction or resistance.
Always keep your blade sharp and carefully maintained throughout its lifespan in order to stay safe when using this useful tool.
- Always remember that safety comes first when using any kind of power tool.
- Your pole saw’s blade works best if it remains at the same angle each time you use your saw.
- Keep your pole saw’s blade sharpened and free of rust, which will extend its life significantly.
- Wearing appropriate safety gear is recommended when working with any kind of power tool, including pole saws.
- Sharpening your pole saw’s blade should be done at least twice per year for peak performance. you can also sharpen it after every few cordless charges or whenever clogged by debris to ensure clean cuts are made every time you’re finished using your tool.
Pole saws are great for large tasks that require extra height in order to complete. However, their blades need constant attention in order to stay sharp and free of any potential dangers when cutting through large objects with them.
The best way you can prevent yourself from accidentally injuring yourself is by keeping your pole saw’s blade as sharp as a razor at all times by performing regular maintenance on it, which should only take a few minutes of your time.
I have shown you how to properly sharpen a pole saw blade without the use of expensive equipment, so there should no longer be an excuse for not keeping this part cleaned off at all times.
With the proper care and upkeep for this utensil, you will save money from having to purchase a replacement blade as well as keep yourself from experiencing any serious injuries.